Heat management devices for hookah (hookah or shisha HMDs) are a vital component of any hookah setup. They are used to regulate the temperature of shisha tobacco, ensuring a smooth and flavourful smoking experience. However, over time, these devices can become dirty due to the accumulation of burnt shisha tobacco.
In this article, we will show you how to quickly clean a heat management device from burnt shisha tobacco so that you can enjoy your hookah sessions to the fullest.
Step 1: Allow the Heat Management Device to Cool Down
Before cleaning a heat management device, it’s essential to make sure it has cooled down completely. Attempting to clean a hot device can cause injury or damage to the device.
Therefore, wait until the device has cooled down entirely before proceeding with the cleaning process.
Step 2: Soak the Heat Management Device in Hot Water
Fill a bowl with hot water and place the heat management device in it. Make sure the device is fully submerged in water. Let it soak for 10-15 minutes.
This will help loosen any burnt shisha tobacco residue that is stuck to the device.
Step 3: Scrub the Heat Management Device
After the device has soaked, use a soft-bristled brush or a toothbrush to scrub away any remaining burnt shisha tobacco residue. Be gentle, as you don’t want to damage the device.
Step 4: Rinse the Heat Management Device
Once you’ve finished scrubbing the device, rinse it thoroughly under running water.
Make sure to remove all soap residue.
Step 5: Dry the Heat Management Device
Use a clean towel to dry the heat management device thoroughly. Make sure to dry all parts of the device, including the metal plate and rubber grommet.
If there are any remaining water droplets, use a hairdryer on a low setting to dry them.
→ Even the best hookah HMDs need proper cleaning!
Cleaning a heat management device from burnt shisha tobacco may seem daunting, but with these simple steps, it can be done quickly and easily. By following this guide, you can keep your heat management device in top condition, ensuring a smooth and flavorful hookah experience every time.
→ Methods to clean an HMD from burnt shisha tobacco:
| Method | Procedure |
|---|---|
| Water | Hold the HMD in hot water and use a cloth or sponge to remove the dirt. |
| Scorching | Heat the HMD on a gas stove, burning the remaining contaminants. Remove the particles with a toothbrush. However, this method should be used with caution as the metal can become deformed from strong heat. |
| Boiling in baking soda | Let the water come to a boil, put 2-4 teaspoons of baking soda in a container, and drop the HMD into the mixture. Boil for 10-30 minutes, depending on the dirt. Remove the residue with a stiff sponge or toothbrush. |
| Cleaning holes with a needle | Use an awl, needle, or toothpick to clean the holes in the HMD. Heat the device in hot water and go over all the holes. |
| Boiling in baking soda and salt | Mix baking soda and coarse salt in equal parts and add to boiling water. Boil the HMD for 10-30 minutes, depending on the dirt. Remove the residue with a stiff sponge or toothbrush. |
| Baking soda and vinegar | Rub baking soda on the HMD with a toothbrush and drizzle with vinegar. Clean the surface. Repeat the procedure 3-5 times until the surface is completely clean. |
| Boiling in citric acid | Add a packet of citric acid to 1 litre of water and boil it. Place the HMD with tongs for 30 seconds. Take out, and remove coarse particles. Repeat the procedure 3-5 times. Turn off the fire and dip the Heat Management Device for 10-20 minutes for a shiny finish. |
When it comes to cleaning a heat management device (HMD) from burnt shisha tobacco, it’s crucial to know which methods to use and which to avoid. It’s highly recommended not to use chemicals or hard metal brushes as these can damage the HMD and affect the taste of smoke. Instead, gentle methods of cleaning should be used to preserve the HMD’s properties and ensure a clean taste of smoke.
The most simple and effective way to clean an HMD is by using hot water. This can remove up to 70% of the dirt.
It’s important to note that each method should be used carefully and for the appropriate amount of time depending on the level of dirt. By following these methods, you can effectively clean your HMD from burnt hookah tobacco at home and preserve its properties for a clean taste of smoke.
How to Clean Your Hookah In 3 minutes by FUMARI.
Hope you have found this article useful.
If you’re looking for accessories to clean your hookah, feel free to browse our care and clean accessories.
Or you simply visit our best online hookah shop
